–10–
STANDARD PROGRAMMING
There are a few programming steps you must perform before the dialer can
operate. Please follow the instructions below to program these fields, including:
- Record voice messages
- Phone numbers you wish to dial during emergency (up to 9 phone numbers)
- Program the panic button or alarm panel to the dialer
When you first power up the Dial Alert, the display will show “not rEAdy”, that
means you don’t have a voice recording and no phone number programmed.
You must perform the following programming steps in order for the Dial Alert
to function during an emergency.
Note: During programming, there is a 10 second time out meaning each
step must be completed within 10 seconds.
RECORD A VOICE MESSAGE
You must record a message and program at least one phone number in
order for the Dial Alert to work. The Dial Alert has 2 different message types:
1) Primary Message, which is 9 seconds long and will always be playback;
2) 5 Secondary Messages, these are event related messages. Messages 1
to 4 corresponds to zone 1 to 4 activation. If zone 1 sensor is activated,
message 1 will be playback. Zone 5 message is for panic button activation
on keychain or keypad remote. The duration for each secondary message is
5 seconds.
Record all the information you would like to be played in case of an
emergency. For example: the primary message, ‘This is an emergency
message from John Smith, please send help to address …...”. The
secondary messages, for example, ‘Zone 1 sensor is triggered’ to be
recorded in message 1 and ‘Zone 2 sensor is triggered’ to be recorded in
message 2 and etc. When the programmed control panel is triggered in the
corresponding zone, the corresponding messages 1 to 5 will be playback.
1. Enter the current password (factory default password is 0000), then press
[PROG], display will show [P] meaning you are now in programming
mode.
2. Enter [3] which represents voice recording. You will see [P3 0 09]. The
number following P3 is the message number, 0 is the primary message
(max 9 seconds) and 1 to 5 represent messages 1 to 5, each can be 5
seconds. The most right digits represents the voice recording duration,
09 mean 9 seconds.
–11–
MESSAGE PLAYBACK
If you would like to listen to the recorded message, you can playback the
message by following the instructions below.
1. Press [ ], display will show [PLAy 0 09] meaning you are now in
voice message playback mode.
2. Enter [0] which represents the primary message to playback. Or enter a
value from 1 to 5 which represents the messages 1 to 5 to playback.
3. Display now shows something like [PLAy 0 05] where the last 2 digits
represent the duration of the voice message you have recorded. Press
[ ] will playback the recorded message.
STANDARD PROGRAMMING
3. Enter [0] to [5] to select which message you would like to record. If you
enter [3], you should see [P3 3 05].
4. To start recording, press [ ] button. You now can start to record the
voice message. The number will decrease and voice recording will stop
when it reaches 0. You may also press [ ] at anytime to stop the
voice recording.
5. After recoding the message, you will hear the recorded message. After
the message playback, it will quit from programming and return to
standby mode.
6. The display still shows “not rEAdy” because no phone number has
been programmed.
Number Representing
Voice Message
Message Type Max. Length (sec.)
0
1
2
3
4
5
Primary Message
Zone 1 sensors
Zone 2 sensors
Zone 3 sensors
Zone 4 sensors
9
5
5
5
5
5Panic Button on Keychain
or Keypad Remote
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals