Skylink DM-50 User Manual download pdf (Page 12)

–

4. Selecting the door type

You must select whether you have an inswing left or inswing right

door. Follow the procedures below to set the correct door type.

4.1 Before powering up the operator, the proper door configuration

must be selected. To select the door type as in-swing right,

please set “Door Type” slide switch to the lowest position. To

select the door type as in-swing left, please set “Door Type”

slide switch to the highest position, which represents in-swing

left door configuration.

4.2 Before the adapter is plugged in, press and hold the "Door

Setting" button (red color button). While holding down the "Door

Setting" button, plug in the power adapter to the adapter socket

on the door operator. Red LED will be on and the orange LED

will flash rapidly and the buzzer will beep rapidly. You may now

release the “Door Setting” button.

4.3 Once the button is released, the orange LED will flash slowly

and the operator’s shaft will start to rotate and perform a

routine startup procedure automatically in order to set itself

up for this door type.

4.4 When the startup procedure is completed, you will hear 2 beeps,

and the motor will stop.

4.5 You should now disconnect the power adapter from the operator

and proceed to the next step. The power adapter should not be

connected again until step 7.

4.6 You may now install the 2 side covers to the operator by sliding

them onto the side of the operator.

CAUTION

When the operator is in "Door Setting" mode.

The motor and its shaft will rotate. ENSURE

NOTHING IS TRAPPED BETWEEN THE

SHAFT AND THE OPERATOR.

INSTALLATION - IN SWING

Door Setting

Button (red)

5. Mounting the operator assembly with mounting plate onto the door

5.1 You may now mount the operator with the mounting plate on the door. It should be mounted on the upper left

corner of the door for in-swing right, or upper right corner for in-swing left.

TODOR

Note: In-Swing Right door installation shown. Note: In-Swing Left door installation shown.

TODOR

In Swing Right

Adapter socket

In Swing Left

Step 1) Press and hold the

door setting button. (red)

Step 2) Plug in the adapter,

buzzer will beep

rapidly.

–

OPERATION

Advanced programming / operations

You have successfully setup the swing door opener and it can perform all the basic operations. There are some

advanced features that require additional programming. If you would like to enable these features, follow the

instructions below. These additional features / programming are:

- Learn / Erase remote

- Different operating modes

Learn remote controls

You can program up to 15 single button - remotes to the swing door opener. This is ideal if you have multiple users

for one door and they can carry their own remotes. To program remote controls, follow the instructions below:

1. The operator should be in standby mode, i.e.

adapter plugged in but the swing door opener

should not be operating, only the red LED should

be on steadily.

2. Press and hold the “Learn” button, the red LED

will start to flash and buzzer will beep indicating

the door opener is not in learn mode.

3. Press and hold the button on the remote you

would like to program while you are holding onto

the learn button on the door opener, you should

hear a long beep and the LED will be off. You

may now release both the learn button on the

door opener and the button on the remote. You

have now successfully programmed the remote

to the door opener.

Erase remote controls

In order to erase any unwanted remote controls (buttons), you must first erase all of them. Then reprogram each

remote (button) you wish to use.

To erase all remote controls:

1. Unplug the door opener when it is in standby mode.

2. Press and hold the learn button, then plug the adapter back in while holding the learn button.

3. You should see the red LED flashing and buzzer beeping rapidly. This indicates all the remotes have been

erased and you may release the learn button. You can now program the remote you wish to use based on

the instructions “Learning remote controls”.

Operating Modes

The door opener can operate in different operating modes, the 3 different operating modes are:

- Toggle (factory default)

- Open / Close

- Timer

Learn button

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Comments to this Manuals

No comments

Skylink DM-50 User Manual Page 12

Comments to this Manuals

Related products and manuals for Kitchen Skylink DM-50