SkyLink GS1 User Manual download pdf (Page 2)

You can add up to 10 additional

transmitters to control the GB-318.

Skylink

offers different

lighting control / automation

transmitters, Visor Transmitters,

Keychain Transmitters and Keypad

Transmitters to work with your receiver.

13. WARRANTY

If, within one year from date of purchase, this product should become defective

(except battery), due to faulty workmanship or materials, it will be repaired or

replaced, without charge. Proof of purchase and a Return Authorization are required.

14. CUSTOMER SERVICE

CUSTOMER SERVICE

17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3

Email:[email protected]

http://www.skylinkhome.com

P/N. 101Z865-002

Patent Pending

® are registered trademarks of their respective corporations

11. WARNING

DO NOT let children use the garage door transmitter without adult supervision.

Otherwise, Children and others may be injured by the garage door.

12. FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference

received, including interference that may cause undesired operation.

WARNING:

Changes or modifications to this unit not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

9. OPTIONAL ACCESSORIES AND OPERATIONS

For more information, please visit our website at www.skylinkhome.com

or contact us.

8. TRANSMITTER PASSWORD PROTECTION

Password protection

The G6T3 can be password protected. If you enable the password pro-

tection, you can only operate G6T3 after you input the correct password.

Password can be 2-8 digits long, which is a combination of 1, 2 and 3.

For example, password can be 1, 2, 1, 2. To input this password, you

have to press [ ], then [ ], then [ ], then [ ].

Note:

[ ] = Button 1 [ ] = Button 2 [ ] = Button 3

Note:

The time-out period is 1 second during above password input.

The factory default password is 2, 2, 2, which is disabled out of factory.

Change password

1. Press 1 and 3 simultaneously and hold for more than 6 seconds until

the LED changes from flashing quickly to flashing slowly.

2. Input old password.

3. Press 1 and 3 simultaneously to confirm. If the password is wrong,

the LED will flash 3 times and you have to start it over from step1.

4.Input new password.

5. Press 1 and 3 simultaneously to confirm.

6.Input new password again.

7. Press 1 and 3 simultaneously to RE-confirm. If the password is

different from the one of step 4, the LED will flash 3 times and you

have to start over from step 1. Otherwise, the password has been

changed to the new one and the password protection is enabled.

Disable password

1. Press 1 and 3 simultaneously and hold for more than 2 seconds until

the LED flashes quickly but not until the LED flashes slowly.

2. Input old password.

3. Press 1 and 3 simultaneously to confirm. If the password is correct,

the password protection will be disabled.

Enable password

1. Press 1 and 3 simultaneously and hold for more than 2 seconds until

the LED flashes quickly but not until the LED flashes slowly.

2. Input old password.

3. Press 1 and 3 simultaneously to confirm. If the password is correct,

the password protection will be enabled.

You can toggle the two states - password protection enabled or disabled.

Note:

The time-out period is 10 seconds during any of the above setting

operations. After 10 seconds, the LED will flash 3 times and the remote

will exit from setting.

If you forget your password and want to reset G6T3, follow the

steps below:

1. Press 1 and 2 simultaneously and hold for more than 10 seconds until

the LED flashes.

2. After you release 1 and 2, the LED will be turned off and G6T3 will be

reset. The password will be reset to factory default.

After the reset, password protection is removed but the remote can not

control any receiver until you reprogram it to receivers you want to control.

Button [ 1 , 2, 3 ]

Program additional remote controls

Smart Button

GB-318 can learn up to 10 remote controls.

To learn additional remote controls, follow the instructions below:

1. Press the learn button on the side of the GB-318.

2. Once the learn button is pressed, the LED will

flash quickly. Release the learn button.

3. Within 30 seconds, press the button on the remote

control you would like to program.

4. Once the remote control is programmed, the LED

will flash slowly, in the same way as it flashes

in standby mode.

5. You may now operate the garage door opener

with this remote control.

Learn Button

Attach visor clip

to bracket.

Stick the

double sided tape on

the back of the bracket.

Peal off the double

sided tape cover.

Mounted on the windshield

Mounted on the visor

7. TRANSMITTER MOUNTING METHOD (CONT)

If you would like to

- find out the up-to-date specifications

- know more about features and applications

- download documents, i.e. user’s instructions

- order Skylink products

or if you have difficulty getting products to work, please:

1. visit our FAQ section at www.skylinkhome.com, or

2. email us at [email protected], or

3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.

Fax (800) 286-1320

LED

3 Volt lithium battery (CR 2032) (included).

It is time to change the battery when the red LED on the transmitter does

not turn on when either button is pressed.

10. BATTERY

1 2

Comments to this Manuals

No comments

SkyLink GS1 User Manual Page 2

Comments to this Manuals

Related products and manuals for Garage Door Opener SkyLink GS1