Note: If you experience interference from a
nearby system, which could accidentally
trigger your system, please change the
code settings on the sensor and receiver.
The code setting on the sensor and receiver
should still match after changing the code
setting.
1. INTRODUCTION
Garage Door
Monitor
TM
Sensor Model GM-434T
The garage door monitor
TM
sensor is designed to monitor the status of
your garage door and advise you if the door is open. By placing the
sensor on the door panel, you will be alerted when the door is open.
When the garage door is open, receiver will beep and flash.
In this package, you should find a garage door monitor
TM
sensor, 3V
lithium battery, double-sided foam tape, mounting accessories and a clip.
Please follow the instructions below to set up your garage door monitor
sensor properly.
4 pcs 3 x 18 screws
1 pc 2 x 5 screw
Garage Door
Monitor
TM
Sensor
Double-sided foam tape
Clip
3V Lithium
battery
Mounting plate
In order for the sensor to communicate with the receiver properly, the
sensor’s code must match with the receiver’s code. Code connectors 1
to 6 can be found by opening the top cover of the sensor and the back
cover of the receiver. User is required to set these code connectors
randomly and the code settings on the sensor and receiver must be the
same. Each position of the code connector can be set to “+”, “-” or “0”
position. Refer to the diagram below to set the code connectors
properly. If the connector is placed on the top and middle posts, that
column is set on “ + ”. If the connector is placed on the middle and bottom
posts, that column is set on “ - ”. If the connector is removed completely,
(not placed on any posts), it is set to “ 0 ”. (see diagram for examples of
how to set a column to the three different positions).
1. CODE CONNECTORS
‘+’
‘-’
‘0’
Code Connectors on Sensor
Open the top cover
Clip
Note: A connector can
be removed with the
clip, as shown.
Each receiver can work with up to 4 different sensors (to represent 4
different zones on the receiver). There are 2 connectors that determine
the zone number 1, 2, 3 and 4. These 2 connectors can be found by
opening the top plastic cover, near the code connectors with marking “A” &
“B”. Please follow table 1 to set the zone.
2. ZONE CONNECTORS
“+” in the table means the connec tor for that position should be placed on
the posts.
“-“ in the table means the connector for that position should be removed.
A B
Zone 1 + +
Zone 2 + -
Zone 3 - +
Zone 4 - -
Table 1
Zone
connectors
2. SET UP THE GARAGE DOOR MONITOR
TM
SENSOR (CONT)
After setting up all the connectors, the sensor is ready to be powered up.
Re move the top cover on the sensor and insert the 3V lithium battery to the
sensor as shown in the diagram.
After insert the battery to the sensor, the receiver will respond to the
transmitted signal depending on the orientation of the sensor.
Insert 3V lithium battery to the sensor
“+” positive
side up
If the sensor is face up in the vertical position, the
green LED on the receiver will glow steadily,
indicating the sensor is in a closed position.
If the sensor is face down in the horizontal
position, one of the red LED on the receiver will
flash, and the buzzer on the receiver unit will also
emit beeping to indicate a door is open.
You can change the orientation of the sensor and
you should see the change in response of the
receiver. If the sensor and receiver are working
properly in close proximity, you can now begin to
install the sensor onto your garage door.
NOTE: It is normal to hear a rattle from the
sensor when tilted or rotated to another position.
Vertical
Horizontal
3. POWER UP THE GARAGE DOOR MONITOR
TM
SENSOR
4. INSTALLATION
Attached the sensor to the garage door with double-sided foam tape if the
surface of your garage door is smooth and clean enough to provide a
good adhesive surface, such surface can usually be found on a metal
garage door. Please ensure the surface is smooth and clean.
For wooden garage doors, it is recommended to use the mounting plate
and screws as well.
Unplug the power cord of your garage door opener
before installation to ensure power is not connected.
WARNING
2. SET UP THE GARAGE DOOR MONITOR
TM
SENSOR
(4 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals