Skylink MULTI LINK PRO ML-001 User Manual

P/N. 101Z379OCT, 2006PATENTED©2006 SKYLINK GROUPHome Smart Centerwww.skylinkhome.comCUSTOMER SERVICE17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J

–8–INSTALLATION5. After inserting the rechargeable battery, the LOBATT LED will be off if the battery is fullycharged, otherwise it will be on.6. Conn

Enter master 3 beeps for validpassword to password. 1 longprogramming mode beep for invalidpassword.[1] - Master password[2] - Secondary password[3] -

Phone Number ProgrammingYou can program up to 6 Emergency Phone Numbers. When the system is in panic,the control panel will call these phone numbers

Note:- It’s not recommended to program 911, fire station or any emergency services phone numbers into any of the phone memories without their approva

–12–Contact ID Phone numberYou can program a telephone number for calling to the central monitoring station.When the system is in panic, the control p

–13–INSTALLATIONAccount Number ProgrammingIn order to program the account number, follow the procedures follow:Press [PROG]Press [MPIN]EnterProgrammin

–14–INSTALLATIONDeactivating the Digital DialerYou can deactivate the digital dialer by erase the phone number memory forcentral monitoring station.Pr

Part 2 Learn signal from Control Panel to Control ModuleHOME AUTOMATIONControl Module [1] is represented by zone LED 1CONTROL MODULELOCATION1 62 73 84

Part 1 Learn signal from Control Module to Control PanelHOME AUTOMATIONZONE LED DESCRIPTIONOff Zone is not occupied by any control moduleFlashes once

–17–The Control Panel can be used to control lights and home applicances with aControl Module, (Control Module is sold separately). Garage door open

Home Smart CenterUSER'S INSTRUCTIONSEnglish

OPERATIONNote:- Each zone can program up to 2 sensors. There are 5 zones, so up to 10 sensors can be programmed to the control panel. Please refer

–19–MuteWhen the alert beeping becomes undesired, you can terminate the beeping in 3different ways:1. Mute button - Manual mute by pressing themute bu

The control panel continuously monitors the system status as well as all thesensors status. It will monitor occurrences such as triggered sensors, lo

–21––36–Note:- The control panel cannot be armed if there are triggered sensors. Make sureall sensors are in closed position, i.e. (close all doors,

Disarming a triggered control panelIf "System Panic" is announced from the control panel after it has been disarmed,that means the alarm was

–23–ADVANCED PROGRAMMINGTo enable alert zone feature, follow the instructions below.1234Enter Program-ming modeEnter masterpassword toprogramming mode

–24––33–Zone 1DISABLEAUTO MUTEButton [1]ENABLEAUTO MUTEZone 2Zone 3Zone 4Zone 5Button [2]Button [3]Button [4]Button [5]Button [6]Button [7]Button [8]B

–25–Keychain Remote (For ML-100 Only)The battery of the keychain remote (Alkaline, Type 23A, 12V) needs to be replacedwhen either one of the following

–26–Receiving the Emergency CallIf you are on the list as one of the recipients of the emergency call, you should readthe following instructions caref

–27–Remote Operation by TelephoneThe control panel can be operated while you are away from home. You canhave access to the control panel with any tou

IMPORTANT SAFETY INSTRUCTIONSWhen using your telephone equipment, basic safety precautions shouldalways be followed to reduce the risk of fire, elect

–29––28–ADVANCED PROGRAMMINGAdvanced Programming allows users to customize the control panel to reactdifferently under different conditions. Features

–2–IC Statement‘’This product meets the applicable Industry Canada technicalspecifications.”Before installing this equipment, users should ensure that

–3–CONTENTIntroduction...4Overv

–4–INTRODUCTIONOverviewCongratulations on your purchase of a Home Smart Center. This is a securitycontrol panel which not only functions as a securit

INTRODUCTION–5–• One AC adapter• One telephone cord• Batteries for all sensors (For ML-100 Only)- 1 PC 9V Alkaline Battery (PS-101)- 1 PC 12V Alkaline

INTRODUCTION]14151. Zone LEDs2. Numeric Keypad3. Arm button4. Status button5. Mute button6. Panic button7. Power LED8. Arm LED9. Program LED10. System

–7–INSTALLATIONInstalling the ConsoleIt is important determine where the control panel will be located. Please followthe criteria below to select the