–22–
If you have sensor(s) programmed to the Dial Alert, you should arm the Dial
Alert if you want to receive notification when the sensor is activated. If the
Dial Alert is not armed, sensor activation will not trigger the dialer. Therefore,
please arm the system when you want to be notified of sensor activation,
such as when you are away from home. If you are home, you may disarm
the Dial Alert if notification is not needed.
ADVANCED PROGRAMMING
DIAL-ALERT QUICK GUIDE
[PIN]+[PROG]+[1]
[PIN]+[PROG]+[2]
[PIN]+[PROG]+[3]
[PIN]+[PROG]+[4]
[PIN]+[PROG]+[5]
[PIN]+[PROG]+[6]
[PIN]+[PROG]+[7]
[PIN]+[PROG]+[8]
[PIN]+[PROG]+[9]
[PIN]+[PROG]+[0]
[PIN]+[PROG]+[*1]
Operating Mode
Change Password
Voice Message Recording
Phone Number
Program Sensors / Transmitters
Erase Sensors / Transmitters
Calling Time
Entry / Exit Delay
Pick up Pause
Dialing Sequence
Universal Dial Tone
2
0000
N/A
N/A
N/A
N/A
45 sec.
Instant
5 sec.
1
2
[1] - Sensor Mode, [2] - SC-001 Mode
Any 4-digit password
[0] - Main Message, [1-6] - Secondary Messages
[1-9] Up to 9 phone numbers
Program up to 16 sensors / transmitters
Erase all sensors / transmitters
[1]-30, [2]-45, [3]-60, [4]-75, [5]-90 seconds
[1] - Instant, [2]-30, [3]-45, [4]-60, [5]-75 seconds
[1] - 1 sec, [2] - 2 seconds....... [9] - 9 seconds
[1] - Off, [2] - On
[1] - Dials each number once, then redial if
necessary,
[2] - Finish dialing first phone number then
begins second number
Factory
Default
SettingsFunctionsProgram #
CONNECT THE DIAL-ALERT WITH YOUR EXISTING ALARM SYSTEM
You may connect your existing alarm system with the Dial-Alert so that the dialer
will be triggered by your alarm system when it is activated. There are 2 ways you
can connect your dialer with your existing alarm system.
1. Connect the dialer with the alarm system
using hard wire (normally closed).
2. Connect the dialer with the alarm system
using the Audio Sensor (AS-101).
Follow the diagram below for hardwiring
the dialer with the existing alarm system.
Every time the alarm system is activated, it will automatically trigger the dialer
to dial out all the preset telephone numbers and play the pre-recorded message.
The other way to trigger the dialer by the existing
alarm system is to use the Audio Sensor AS-101
in conjunction with the Dial-Alert, (see Additional
Accessories page 24).
PANEL OR SENSOR
N.C.. LATCHING
DRY CONTACT*
(NORMALLY CLOSED
OPENS ALARM)
AD-105
Remove the
jumper first
Place the Audio Sensor beside the siren of your
existing alarm system, once the alarm is activated,
the siren will sound and the Audio Sensor will be
triggered and send a signal to the Dial-Alert to
activated it. There is no wiring involved in this case.
Remove the jumper first
The AD-105 Dial-Alert comes with 1 battery that at some point you may
have to replace:
One 9 volt alkaline battery for the Dial-Alert
Recommendation: Test your Dial-Alert periodically to ensure that the battery
is working.
Dial-Alert Battery
The Dial-Alert comes equipped with a 9V backup battery in case the elec-
trical power is interrupted for any reason.
When the dialer backup battery is low, the LOBATT. light goes on.
To replace the dialer backup battery:
1. Undo the two screws on the back of the
Dial-Alert.
2. Open the Dial-Alert case by pressing
down on the two tabs on the top edge
and pull the front forward.
3. Disconnect the old battery.
4. Connect the new battery.
5. Close the Dial-Alert case and re-insert the
two screws.
The battery life, (9 volt alkaline battery), is approximately two years if used
only for backup.
–23–
BATTERY MAINTENANCE
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals