SkyLink GT-100A Instruction Manual download pdf (Page 3)

Operation

3. OPERATION (CONT)

Push Button

Press the push button to open or close the garage door.

Lock Button

Lock feature is designed to prevent Skylink

handheld

remotes such as Skylink

Keychain Remote Model 4B-201

(sold separately) to operate the garage door opener.

To activate the lock feature

1. Press and hold the lock button for approx. 2 seconds, then release it.

2. When the lock feature is activated, the red LED underneath the push

button will flash rapidly.

Note: If a valid wireless remote signal is received while the lock feature is

activated, wall console will beep to reminding you the wall console is locked.

To deactivate the lock feature (unlock)

1. Press and hold the lock button for approx. 2 seconds, then release it.

2. When the lock feature is deactivated, the red LED underneath the

push button will flash slowly indicating the wall console is in normal

operating mode and the lock feature is deactivated.

If you have a Chamberlain

, Lift-Master

, or Sears

Multi-Function Wall

Console, the lock button will lock/unlock both the Skylink

handheld

remote, as well other Chamberlain

, Lift-Master

, Sears

remote

controls.

Learn Button

Skylink

Wall Console can be used as a garage door opener receiver. It

does not only operate as a garage door closer, additional handheld remote

controls can be added. Additional remote controls are sold separately.

To program Skylink’s remote control / sensor

1. Press the learn button for approx. 5 seconds.

2. The “Timer / Learn” red LED will be on, release the learn button.

3. Activate the Skylink

remote control. If the Skylink

remote control has

multiple buttons, press the button you would like to operate.

4. The “Timer / Learn” LED will be off after it has successfully programmed

the remote control.

5. You can now press the programmed remote to operate the garage

door opener.

If you have a Chamberlain

, Lift-Master

, or Sears

Multi-Function Wall

Console, the learn button also works as a light button. Pressing this

button slightly will turn the light on the garage door opener on / off.

Push button

Timer / Learn LED

Loss of Signal LED

Learn buttonLock button

3. OPERATION (CONT)

Antenna

Turn light on / off

Open / Close door

- Chamberlain

- Sears

- Liftmaster

– 3–

Erase Skylink

remote controls / sensors

To erase unwanted remote control(s), first erase all remote controls and

sensors, then program the ones you would like to keep.

Erase all remote controls / sensors

1. Press and hold the learn button for 15 seconds.

2. The “Timer / Learn” red LED will flash rapidly meaning all remote have

been erased.

3. You have now successfully erased all the remote controls and sensors.

Follow the instructions “To program Skylink’s remote control” to add

the remote control(s) you would like to keep.

Important!

Ensure both the lock and light functions operate properly. Depends on

which mode you are in:

Lock Button Light Button

Full Function Mode* Lock /Unlock both GC-433R and Turn light on / off

Garage Door Opener

Simple Mode Only lock / unlock GC-433R No Function

* For Chamberlain

, Lift-Master

, Sears

Wall Console ONLY.

Pressing these buttons on the GC-433R should not activate anything

else, such as opening or closing the garage door. If it does, you may

need to change between Full Function Mode and Simple Mode. Refer to

“Garage Door Opener operating Mode” below.

Lock / Unlock

Loss of Signal

Skylink

Wall Console also monitors the status of the garage door sensor.

If the garage door sensor fails to communicate with the wall console, the

loss of signal LED will flash indicating a trouble condition for the sensor.

There are 2 types of sensors. The flashing is different depending on the

type of sensor:

Garage Door Sensor: One flash at a time

Audio Sensor (Optional Accessory): Two flashes at a time

When the loss of signal is flashing, please check the following:

- Check the battery of the sensor.

- The LED on the sensor should flash when the sensor is triggered.

For the detail of how the Audio Sensor works, please refer to “Accessories”.

Garage Door Opener Operating Mode

The operation for different brands of opener is slightly different, so

while the GC-433R is charging, it also identifies the brand of your

garage door opener. Mainly there are 2 operating modes:

Full Function Mode: Chamberlain

, Lift-Master

, Sears

with Multi-Function

Wall Console

Simple Mode: Other brands

1 2 3 4

Comments to this Manuals

No comments

SkyLink GT-100A Instruction Manual Page 3

Comments to this Manuals