SkyLink WR-001 User Manual download pdf (Page 3)

Input Voltage: 120V AC, 60Hz

Maximum Load: 600W at 120VAC

Operating Frequency: 318MHz

Range: Up to 500 feet in open area

Standby Current: 0.2mA

Minimum Load: 10W

Operational Temperature: -4° F - 140° F (-20° C - 60° C)

Humidity: 5%-95%

10. TECHNICAL SPECIFICATIONS

11. FCC

The Device is approved by the FCC and it complies with Part 15 of the FCC Rules.

Its operation is subject to the following two conditions :

1. This device may not cause harmful interference.

2. This device must accept any interference that may cause undesired operation.

WARNING:

Changes or modifications to this unit not expressly approved by the party responsible

of compliance could void the user’s authority to operate the equipment.

13. CUSTOMER SERVICE

CUSTOMER SERVICE

17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3

Email:[email protected]

http://www.skylinkhome.com

P/N. 101Z713

Patent Pending

9. ERASING TRANSMITTERS FROM THE MODULE

You may erase a transmitter or sensor from the wall dimmer, but you

cannot erase a specific device directly, you must erase all the wireless

devices, then program the ones you want to keep. Follow the instructions

below to erase programmed transmitters / sensors.

1. Power off the Wall Dimmer by placing the air gap switch to off position.

2. Press and hold the SET button, while holding the SET button, slide the

air gap switch to on position.

3. The blue LEDs will be on first, then flashes rapidly for 1 second.

4. You may release the SET button, now you have successfully erased all

the devices.

14. ACCESSORIES

The Skylink System consists of many other devices such as

SkylinkHome Remotes, Motion Sensor, ON/OFF Wall Switch, Wall

Dimmer, Plug-In Dimmer with or without Repeater, Plug-In ON/OFF

Control (Outdoor/Indoor), Screw-In Dimmer, ON/OFF/Dimming Control,

ON/OFF Control, Smart Button Garage Door Control, etc. Please visit

Skylink website at www.skylinkhome.com for more information.

Home

V2.0

8. ZONE OPERATION

12. WARRANTY

If, within one year from date of purchase, this product should become defective

(except battery), due to faulty workmanship or materials, it will be repaired or

replaced, without charge. Proof of purchase and a Return Authorization are required.

An optional deluxe remote is needed for zone operation. A Zone Command

allows you to operate multiple lights altogether in the same zone.

A zone command must first be programmed to the receiver before zone

operation. To program a zone command, please refer to the user's

instructions of the deluxe remote.

Zone Operation - On / Off

To turn on or off a zone, hold [ ] or [ ] until the red LED flashes

three times and keeps on, then release the held button and press the

zone number.

For example:

Hold [ ] until the red LED flashes three times and keeps on, then

release [ ] and press [1], all lights in zone 1 will be turned on.

Hold [ ] until the red LED flashes three times and keeps on, then

release [ ] and press [1], all lights in zone 1 will be turned off.

Zone Operation - Brightness Control

You can also change the brightness of lights in a zone altogether, if the

receiver modules and all lights connected are dimmable. If non-dimmable

lights or appliances are connected to a zone, do not operate Zone

Brightness Control.

For example:

Hold [ ] until the red LED flashes three times and keeps on, then

release [ ] and hold [1] , all lights in zone 1 will be brightened, you

may release [1] at the desired brightness level.

Hold [ ] until the red LED flashes three times and keeps on, then

release [ ] and hold [1] , all lights in zone 1 will be dimmed, you

may release [1] at the desired brightness level.

If you would like to

- find out the up-to-date specifications

- know more about features and applications

- download documents, i.e. user’s instructions

- order Skylink products

or if you have difficulty getting products to work, please:

1. visit our FAQ section at www.skylinkhome.com, or

2. email us at [email protected], or

3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.

Fax (800) 286-1320

1 2 3

Comments to this Manuals

No comments

SkyLink WR-001 User Manual Page 3

Comments to this Manuals