Skylink TC-318-7 User Manual

Browse online or download User Manual for Remote control Skylink TC-318-7. Skylink TC-318-7 User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 4
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
TM
Thank you for your purchase of a SkylinkHome , Deluxe Remote,
Model TC-318-7 / TC-318-10 / TC-318-14. This transmitter which is also
called remote in this document allows you to wirelessly operate
TM
SkylinkHome receiver modules.
Use this personal remote, you can control almost everything in your home
such as Lighting on / off and dimming in different location, open and close
your gate or garage door, arm and disarm your security system, turn on or
turn off your gas fire place, control radio and music system, operate the
windows curtains, cook your coffee every early morning, open and or close
the swing doors, turn on or turn off the fan or Exhaust fan for your bath room...
TM
All wireless signal communications within the SkylinkHome system are
based on rolling code technology to ensure highest security is used.
The following items are included in this package:
- One of TC Series Remotes
- Mounting Bracket and Accessories
- Lithium Battery CR-2032
- User's Instructions
1. INTRODUCTION
10-Button
Remote
TC-318-10
14-Button
Remote
TC-318-14
Model TC-318-7
Model TC-318-10
Model TC-318-14
7-Button Remote
10-Button Remote
14-Button Remote
The Deluxe Transmitter can transmit 3 types of command:
1) Individual Operation - Controls one light only, i.e. the ceiling light in
the family room
2) Zone Operation - Controls one specific zone or area, which consists
of multiple lights, i.e. all lights in the kitchen
3) All On / All Off - Controls all lights in the premises, i.e. all lights in the
TM
house connected with SkylinkHome lighting modules.
Before you can control the lights (or small appliances, etc.) connected to
the receiver modules with the transmitter, you may need to program
different buttons on the transmitter to various receiver modules. It is a lot
easier if you plan in advance of how to setup your system. For example,
you may list out the lights and their locations with zone grouping that you
plan to include in your lighting system.
Number
Button
Number
Button
1
2
3
4
5
6
7
8
9
10
Light
Light
Zone
Zone
Family Room Floor Light
Family Room Ceiling Light
Kitchen Floor Light
Kitchen Ceiling Light
Bedroom Floor Light
Bedroom Ceiling Light
Master Bedroom Floor Light
Master Bedroom Ceiling Light
Front Yard Light
Back Yard Light
Zone 1
Zone 1
Zone 2
Zone 2
Zone 3
Zone 3
Zone 4
Zone 4
Zone 5
Zone 5
3
4
Back Yard
Zone 5
Kitchen
Zone 2
1
2
Family Room
Zone 1
7
8
Master Bedroom
Zone 4
5
6
Bedroom
Zone 3
Front Yard
Zone 5
You may use the following table to fill in the lights or small appliances
you would like to control and their zone numbers, this will give you a
clear direction during the programming process.
2. PROGRAMMING TRANSMITTERS TO RECEIVER MODULE
In order to operate the receiver module remotely with a transmitter, it
must be programmed to the receiver module. Follow the instructions
below.
Mounting
Bracket
with magnet
Lithium
battery
7-Button
Remote
TC-318-7
Screws and
anchors
2. POWER UP
2. POWER UP (CONT)
To power the transmitter, simply remove the battery isolator from the
transmitter, red LED will flash once. Press the button on the transmitter,
the red LED should flash. The transmitter is now powered properly. If
the red LED does not flash when button is pressed, refer to Section 7
“Battery" of this manual.
1) Remove isolator,
2) LED on for 1 second
LED on for
1 second
Remove
isolator
You may assign the buttons to specific lights and zones.
Programming for Individual Operation
1. Put the receiver module that you plan to program
into programming mode. Refer to the User's
Instructions of that receiver module.
2. Use a sharp object to press the “PROG”
button on the back of the transmitter. The red
LED on the transmitter will be on for 15 seconds.
3. Press the button on the remote that you plan to
use when the LED is steadily on to transmit the
“Learn" code.
4. Once the remote is programmed, the receiver
modules will quit from programming mode and
the programmed transmitter is ready to be
used now.
To program a remote to the receiver module, a "Learn" code must be
transmitted, follow the instructions below to transmit the "Learn" code
to the receiver.
“PROG”
button
Press the
desired
button
Learn Code
Follow steps 2 and 3 above to transmit the "Learn" code when
programming the remote to receiver modules.
Page view 0
1 2 3 4

Summary of Contents

Page 1 - 14-Button Remote

TMThank you for your purchase of a SkylinkHome , Deluxe Remote, Model TC-318-7 / TC-318-10 / TC-318-14. This transmitter which is also called remot

Page 2 - Learn Code

2. PROGRAMMING TRANSMITTERS TO RECEIVER MODULE (CONT) “PROG” buttonProgramming for Zone OperationIn the above example, both the Family Room Ceiling L

Page 3 - with one touch of a button

4. ZONE OPERATION - DIMMING7. PASSWORDYou may control the brightness of lights in a zone. To brighten up multiple lights in a zone:1. Press and hold [

Page 4

Operation with password function enabledIf the password function is enabled, before each operation, the password must first be entered, followed by th

Related models: TC-318-14

Comments to this Manuals

No comments